BBN company machining process center include flame cutting, welding, drilling, grinding and heat treatment service for A572 grade 42 high strength steel products. Flame cutting is to use the high temp
The company received new orders from Peru customer for more than 900 tons of ASTM A36 steel plates ASTM A709 carbon steel plate. These A36 steel plates will be used in the "Belt and Road" project - a
ST37-2 is a kind of low carbon steel with carbon content of 0.20%, similar to S235JR or Q235 A709 grade 50 high strength steel. It's not as strong as common ASTM A36, but it is also widely applied by
The difference between A572 Gr 42 high strength steel, hot rolled sheet and cold rolled sheet: hot rolled sheet has low hardness, easy processing and good ductility. The cold-rolled sheet has high har
The fake and inferior A283 Gr D mild steel coil, steel plates have no metallic luster and are light red or similar to pig iron for two reasons. 1. Its blank is adobe. 2. The rolling temperature of cou
ASTM A709 bridge steel plate and so on steel structure engineering steel has good plasticity, which can make the structure have obvious deformation before being destroyed, so as to avoid brittle failu
Compared with carbon steel, low alloy steel has many advantages, such as high strength, good plasticity and toughness, good weldability, good cold and hot pressure processing performance, better corro
Flat steel is a kind of steel with rectangular cross-section and blunt edges at the edges and corners. It is usually 12-300 mm wide and 3-60 mm thick. Compared with A572 Gr 55 CS steel carbon plate or
Advantages of A283 grade D ms steel sheet: 1. Steel purity: Wugang can produce high purity molten steel with P 0.010%, S 0.005%, N70ppm, O15ppm, H2ppm, and 20ppm total inclusions in the steel. 2. Good
A plasma cutter uses a stream of compressed gas (air, nitrogen, argon, etc.) and a consumable wire electrode as the two primary feedstocks of the steel cutting process. The electrode sends a high elec
BBN STEEL is an agreement direct selling agent of Wuyang Iron and Steel Company, which mainly deals in medium and extra wide and extra thick steel plates. There are more than 8,000 tons of steel A709
The characteristics and scope of application of A709 Gr HPS50W bridge steel plate, No. 55 steel: 55# steel is a high-strength medium-carbon steel with high surface hardness and strength after treatmen
Ordinary medium and thick steel plate ASTM A514 alloy steel plate is a kind of deoxidized steel. The oxygen content of the steel liquid is relatively high, and a lot of gas will be produced during the
Low-alloy steel plates have low carbon content, and because ferrosilicon is not used for deoxidation, the silicon content in steel is often ＜0.07%. The outer layer of rimmed steel is crystallized in a
The work performance of A709 grade 50 low alloy steel sheet etc. steel material is mainly depended on its chemical composition, mechanical properties etc. parameters. The higher strength the steel has
In order to improve the ASTM A573 structural steel plate corrosion resistance and decoration of steel, it is an important content of steel production method to plating or coating a protective layer on
S960Q plate implements standard EN10025-6S960Q plate application: European standard high-strength steel plate, corresponding to the national standard Q960. A572 Gr 65 ms steel coil, S960Q plate is sui
Manganese steel plate is subdivided according to material grade: Q345A, Q345B, Q345C, Q345D, Q345E, A709 Gr 50 low alloy steel sheet. The main differences according to the classification are as follow
There are four grades under the WQ1150 quenched and tempered high-strength steel plates: WQ1150C, WQ1150D, WQ1150E, and WQ1150F, A573 Gr 70 CS steel carbon plate.Analysis of mechanical properties of W
Carbon steel ASTM A573 steel sheet is an iron carbon alloy with carbon content less than 2.11% and a small amount of silicon, manganese, sulfur, phosphorus and other impurities. Carbon steel inevitabl
Q550C steel belongs to low alloy high strength steel. Chemical composition of Q550C steel: C ≤ 0.18, Si ≤ 0.60, Mn ≤ 2.0, P ≤ 0.030, S ≤ 0.030, Nb ≤ 0.11, V ≤ 0.12, Ti ≤ 0.20,
The ASTM A572 A283 Gr C CS steel carbon plate specification refers to high-strength low-alloy steel plates used in structural buildings. Among the five steel grades 42, 50, 55, 60 and 65, grade 50 is
The size, shape, weight and allowable deviation of Q390D, Q390D-Z35 steel plate should comply with the provisions of GB/ T709-2016. The maximum thickness of the steel plate is 135mm. When the ASTM A58